Roofing Inspection: Why Your Roof Needs to Be Inspected

A home’s roof is its primary protection against water damage. That’s why it needs to be inspected periodically to make sure it is in good condition. For professional assistance, contact Roofing Colorado Springs.


The inspection looks at the entire structure of the roof, including the soffit, fascia, and gutters, as well as any skylights or masonry chimneys. Inspectors also look for signs of sagging, stains, mildew, or mold.

When a new roof is being installed, the first thing that a roofing contractor needs to check is the condition of the roof deck. If it’s rotting, it can’t hold the weight of the shingles and other materials that will be attached to it. The International Residential Code requires that the shingles be fastened to solid sheathing. This means that the sheathing must be able to support the weight of the shingles and other materials.

The inspector will look at the sheathing to make sure that it is properly nailed and not rotted. He or she will also verify that the sheathing is thick enough for a roof. Some types of sheathing, such as plank sheathing, require a specific thickness to be in compliance with the code.

During this inspection, the inspector will also look at all areas where the sheathing has been cut to accommodate flashing or other items. He or she will also check that kick-out flashing is in place where needed, especially for chimneys.

If the sheathing is not in good condition, the inspector will note that on his or her inspection report. The inspector will also note if the sheathing is being used for an existing roof, in which case it will be required to have a kick-out flashing in accordance with IRC Section R903.2.1.

A professional will also inspect the joists and beams on the inside of the roof, looking for rust or other damage. He or she will also make sure that joists and beams are properly supported by the framing. The inspector will also look for rust on fasteners, metal connector plates, and joists. The inspector will also note whether the joists are properly spaced and the rafters are plumb.


Many homes have a variety of vents, including gable, soffit, and ridge vents. Each type of vent requires careful inspection to make sure the opening is open and free of obstructions. The home inspector will also check that the prevailing winds are blowing parallel to the vent. If they are blowing across the openings of the ventilation system, the performance of the ventilation system will suffer.

When a roof vent is installed, there must be flashing that covers the opening. The flashing helps keep water from getting into the structure through the gap. Building codes are very strict about this type of flashing, and the inspector will inspect it to see that it is properly installed.

In addition to checking that all the vents are open and in good condition, the home inspector will also look for adequate attic ventilation. He will take the temperature of the attic space and check that bathroom and kitchen exhaust fans vent out the roof. Many older homes did not have this, and the result is that moisture in the attic causes mold problems.

The attic is a dangerous place, and the home inspector will wear a hard hat and safety glasses and carefully walk around the attic beams. He will be looking for any signs of active leaks, such as daylight shining through the attic ceiling or dripping water spots on the ceiling below the attic or in the attic itself, and will also inspect the attic insulation for sagging, looseness, gaps, or other problems. The inspector will also look for the condition of any penetration seals on ductwork, chimneys, plumbing vent pipes, and media installations such as cable TV or satellite dishes.


Many elements of construction go unnoticed, but the flashing that prevents roof leaks is not one of them. This thin protective layer is installed in areas where the walls of a building meet the roof or where structures like chimneys, vents, and skylights intersect with the roof. It also protects against leaks around those structures and creates an airtight seal in other crevices that might otherwise seep into the structure.

It is most often made of copper, aluminum, or galvanized steel. If not properly installed at the time of initial roofing installation, flashing can quickly deteriorate and lead to the leaking that characterizes so many roofing failures. When re-roofing a home, it is generally advisable to replace all of the flashing. But in some cases, a professional roofer might choose to reuse the old flashing if it looks like it is in good condition and would still serve the purpose of directing water away from seams and joints.

During your roof inspection, make sure you check the exposed flashing for any signs of deterioration, particularly in the areas around vents, pipes, chimneys, and skylights. Leaks at these points can penetrate your home’s exterior and even the inside of your attic. Look for areas of flashing that appear to be peeling away from the wall or looking severely corroded.

Roofers install various types of flashing to ensure a watertight barrier. Some are designed to be exposed, while others are embedded. Examples include step flashing, which consists of short pieces of metal that overlap the flashing course below them. This is often found in chimney stacks on pitched roofs and along the edges of dormer windows, which jut out from exterior walls. There is also wall flashing, which is embedded in the interruptions in a wall, such as doors or windows, to prevent water ingress and direct any that does enter back outside.


A soffit is the “skin” that covers the eave of your roof and serves both an aesthetic and functional purpose. Aesthetically, it adds character to your home and can be painted in a variety of colors to match your trim or siding. Functionally, it protects the rafters, or your roof’s support beams, from the elements. Without a soffit, the rafters would rot over time and, if left unchecked, could cause mold to invade your home. Both of these are very expensive to repair.

In addition to protecting the rafters, the soffit also helps keep pests like squirrels and bees out of your home. It also provides ventilation for your attic. If your soffit is not properly vented, it can lead to moisture and mold issues, resulting in water leaks from the roof into the attic. In addition, clogged soffit vents can prevent air flow between the roof and the attic, leading to ice dams and other issues.

Soffits can be made from a variety of materials, including wood, vinyl, and aluminum. However, James Hardie fiber cement soffits are recommended, as they do not rot and can withstand hot climates.

During your roofing inspection, the inspector will check for damage to the soffit and fascia, including peeling paint, cracks, rotting or warping, and other signs of damage. In addition, the inspector will assess if soffit vents are clogged or missing. If necessary, he will recommend that the soffit and fascia be repaired or replaced. If not repaired or replaced promptly, it could result in further damage to your roof and shingles. It is also a good idea to install removable soffit vents on balconies to allow for rapid temperature and vapor equalization, preventing mold, rot, and insect infestation.


The roof shingles are the outermost layer of your home’s shelter. They are affixed to the deck with nails or glue and then covered with granules, a protective barrier from the sun’s damaging UV rays.

Your inspector will walk around the house, checking for popped nails, cracked caulk, and other signs of wear and tear on your shingles. They will also look for shingle edges that have lifted or curled and moss or algae stains.

As the material inspection continues, your inspector will check the flashing that is placed wherever shingles butt up against other surfaces or each other, such as at chimneys or in open valleys. The flashing is a vital piece of the roofing system to keep rain out of your house, so your inspector will make sure that it isn’t rusted and that all of the pieces are still in place.

They will also inspect the eaves and gutters to see if there is any water leaking or overflowing. They will also look for rust on metal gutter downspouts and check the condition of the soffit, including making sure that it is solid and not rotting or allowing water to penetrate.

An interior inspection is also part of the roof inspection, since leaks from a bad roof will ultimately damage the inside of your home. Your inspector will examine ceilings, attics, and walls throughout your home for signs of water stains, mold, or other problems that would indicate that the roof is not working as it should. They will check for proper attic ventilation, which is crucial to extending the life of your shingles. They will also check the rubber boots and seals around vent pipes to make sure they are in good condition.


Roofing Companies

Roofing companies offer a variety of services to their clients. Some specialize in low and steep-slope roofs. Some are willing to work with home improvement finance companies to give their clients financing options. Here are some things to consider when choosing a roofing company. A roofing company should be licensed and insured, and they should be willing to work with you to arrange to finance if necessary.


Roofing companies offer a wide range of services to help you protect your home. As the first line of defense against adverse elements, the roof takes a beating from harsh weather conditions. Even the slightest mistake on your roof can cause significant damage. Here are some tips to help you find the right roofing company for your home.

First, you should always hire a professional roofing company. You should never try to do the repair work yourself because you may end up injuring yourself. Even if it is a simple fix, it’s best to hire a professional. A professional will be able to detect any problems and recommend a solution to them before they escalate.

In addition to roof repair, a roofing company can install various types of roofs, including green, ply modified, and solar roofs. These companies also specialize in performing regular inspections, repairing damages from natural disasters, and installing new roofs for residential and commercial properties.

Roofing contractors can also help you improve the energy efficiency of your home. For instance, you can have ice melt systems installed by a professional roofing company. Or you can choose to add vents. These professionals can do it all, from the smallest to the biggest. Depending on your needs, a roofing company can also provide other services that you might not have thought of on your own.

There are many benefits to a low-slope or steep-slope roofing system. It allows rainwater to run off the roof and leaves the surface dry. It also minimizes the amount of heat that enters the structure. It is a classic design and requires little maintenance.

To determine which type of roofing system to choose, the first step is to determine the slope of your roof. It’s easy to measure the slope of your roof by measuring the vertical rise of the roof in inches. The pitch of a roof can affect the materials used to build it, as well as the amount of maintenance it requires.

The most common type of low-slope roof is made of several layers. First, roofers cover the surface with insulation. After covering the surface with insulation, they add another layer of bitumen. Then, they added another layer of roofing that felt soaked in bitumen. Afterward, they glaze the top layer of bitumen and then insert gravel into the layer.

One thing to keep in mind is that a low-slope roof is more vulnerable to leaks, which is a big problem in these environments. This can be a result of improper installation or inadequate maintenance. Generally, a low-slope roof can last anywhere from ten to twenty years with proper maintenance.

A low-slope roof system provides several benefits for commercial buildings. It provides a bonus floor for foot traffic and can accommodate large pieces of equipment. Additionally, low-slope roofs are more affordable to install and require fewer materials and labor. They are also lighter on structure than traditional shingles, so they are more cost-effective for commercial projects.

A roof with a steeper slope will require more shingles and roofing cement. The cost of materials will increase, but the higher-slope roof will require more labor. Also, the higher-slope roof requires more nails and roofing cement. Therefore, the cost of labor will also increase. In addition to these costs, roofing companies may also carry professional insurance coverage. Often, the higher-risk work requires higher insurance premiums, which means higher costs for customers.

Roofing has a 65-to-35 ratio of steep-to-low-slope roofs. The proportion of steep-slope work is likely to remain consistent over the next five to 10 years. The company’s steep-slope work includes churches, apartment complexes, and residential homes, while its low-slope work includes office buildings, strip malls, and dental practices.

If you need a new roof but don’t want to pay cash, some roofing companies offer financing options. Many of these companies work with banks or other financial institutions to offer affordable financing options. If you have equity in your home, you may also qualify for a home equity loan. The good thing about this type of loan is that you’ll know exactly how much you’re going to have to pay at the end of the month.

Most roofing companies have financing options available for homeowners. These options may include in-house financing through a third party. You can also take out a second mortgage, which uses a portion of your home as collateral. The repayment term is typically between five and thirty years, and you’ll have to make fixed monthly payments for the duration of the loan.


Gutter Removal Tips

If you’ve decided that it’s time to get rid of your gutters, there are some things you should know before starting the job. To remove your gutters correctly, you should first disconnect your downspout from your gutter. To do this, remove the elbow or attachment strap from your downspout. Then, unfasten the sheet metal screws holding the gutter corner pieces together. After you have disconnected them, you can remove them with a pair of tin snips.

Roofing Services

Another important consideration to make is the condition of your gutters. A clogged gutter can signify a larger problem that may require gutter repair. In addition to leaking rainwater, it can cause damage to your siding and roof. A faulty gutter system can eventually collapse. Taking care of this problem is necessary if you’re considering a new roof. You’ll also want to check the gutters periodically to ensure they’re working properly.

Aside from the gutters, other factors must be considered when determining a gutter removal price. Two-story buildings typically require more gutter installation than a one-story structure. The labor involved is much more expensive on two-story homes so gutter replacement companies will charge a higher price. Additionally, there’s a greater chance that the gutters you’re replacing will be damaged soffit or fascia board. The cost of repairing soffit and fascia board is roughly six to $20 per linear foot, and the average cost is $13.

Before you begin the removal process, you’ll need to determine the exact slope of your gutters. This means measuring the slope from the bottom of your fascia board to the nail that holds it to the fascia. Make sure the slope is at least a quarter-inch toward the fascia board. If it’s uneven, you can adjust the gutters’ height by adjusting the fascia board’s string. You can also use an assistant to help you hold the gutter while taking the nails out.

It may be time to consider gutter removal if your gutters are damaged or just plain worn. A damaged gutter can cause significant damage to your home. You can choose to have the gutters replaced by an experienced gutter removal company. The cost of gutter removal depends on the type of gutter you have and its location. When the job is complete, you can install a new gutter. After that, you can install rain-harvesting systems to reduce the risk of flooding.

Gutter removal is often necessary when you need to replace your home’s roof. A simple tear-off and replacement may save you a great deal of headaches. After the removal, you should take into consideration the gutters. You can choose to replace the entire roof with a new roof, but you will have to deal with the gutters. This is a complicated process, so be sure you hire a professional.

Using a ladder to remove the gutters can be dangerous, so wear a helmet. It is also important to choose a ladder that is long enough to reach the height you need. Otherwise, you could cause a lot of strain while trying to remove the gutters. Remember to observe all electricity, battery safety, and safe wiring rules while using power tools. If you use a power drill, be sure to use it in reverse, removing the screws from the gutter.

A downspout outlet is an essential part of the gutter system. The outlet should have holes on the bottom to allow water flow. It will prevent any ice from forming and any corrosion or leaks from occurring. If you want to install a new downspout, you can cut the hole in the bottom with offset tin snips. Once you’ve cut the hole, the next step is to attach the downspout outlet to the new gutters.

Installing new gutters is another important part of home maintenance. Installing gutters that are properly positioned for your home’s style is essential. The overhanging portion of your roof also determines where water will run down the wall or enter the house. If you want to install a new gutter, make sure you allow the overhang to be at least 6 inches. This will prevent the overflow from occurring. It will also prevent the water from penetrating the earth beneath your home.


How to Hire a Roofing Contractor

A Roofing Contractor is an individual who undertakes the construction of roofs, which may be of varying sizes and types. When hiring a roofing contractor, you should research to find out more about his work. The process starts by inviting potential contractors to your home and discussing the type of roofing materials you need and the scope of the job. It would be best if you asked about his manpower and the time needed for the project. Make sure to observe the contractor and ask for references if available.

Roofing Services

Roofing contractors are licensed to work on roofs and other home exterior components. They have the expertise and experience to complete even the most complex projects and overcome unexpected issues. Roofing contractors have the knowledge and expertise to complete a quality job on time. They will be able to estimate the cost of the work and the type of materials needed. If they have any scrap materials or other discarded building materials, they will properly dispose of them. 

In order to become a roofing contractor, you must undergo training. You can pursue an apprenticeship or seek entry-level employment. You will learn about safety practices and proper materials and equipment during training. If you are looking for a career in roofing, experience in construction or roofing is an advantage. You must be able to use hand and powered tools properly and have the ability to stand on ladders for long periods. It would be best if you were physically fit to work as a roofing contractor.

To become a roofing contractor, you must hold a license from the state. Roofing contractors must obtain a license through some state Department of Professional and Occupational Regulation Board. There are three different license classes, and applicants must pass a trade, business, and law exam in order to receive a roofing contractor’s license. You will need to demonstrate you have at least two years of experience in the field before obtaining the license.

Lastly, find a roofing contractor who has an office. Visiting their office will help you see their previous work and ask for references. You can even visit a roofing contractor’s job site to view their work firsthand. A good roofer will be happy to show you his previous work. Also, don’t be afraid to check their website and social media pages. If you can’t find any references, that’s a red flag.

Bonding a roofing contractor may help protect you from paying for a repair or replacement due to an accident or damage to your home. Although there are disadvantages to bonding, the peace of mind it brings can make the cost worthwhile. Bonding is more common on industrial and commercial roofing projects, where higher materials and labor costs. The types of bonds used in these phases differ. If you are unsure whether to hire a roofing contractor, check with your insurance company to see if they are insured.

A roofing contractor must register with the Department of Labor before undertaking any work. Roofing contractors in some states must obtain a C-15a roofing contractor license from the State Contractors Board. If you’re thinking about getting a license, you should have four years of experience within the last ten years. If your state is not required to license contractors, you may be able to get away with not having a license to work in the state.

Another thing to consider when choosing a roofing contractor is their experience. A licensed and insured roofing contractor is likely to stand behind his work. It’s not a good idea to hire a roofing contractor just because he is the cheapest. You can also check on previous jobs with them, which may be advantageous if you ever need to file a claim. If you hire an unlicensed roofing contractor, you may lose your money.